Subaru conversion

2. 排氣管, 下圖為雙孔 head. 配上改裝排氣管

4. 引擎托架, 下圖下方的兩片鐵片, 上方桿子為RMW的引擎吊架.

下圖下方箭頭指示為SMC 引擎托架, 右邊為T3 原廠吊架.

5. 排氣管尾段支架

6.油門線

9. 改裝線組

10.下圖左邊為原場油底殼, 右邊是淺油底殼.

11. 機油尺, 油底殼外接管路即為機油尺管子.

12. 下圖上方為原場水管, 下方為反置subaur 上水管,

SMC convertion kit for review

T3 改裝Subaru EJ2.2/2.5l
以下應該要買

1. Adapter and flexplate ( 自排變速箱轉接扭力盤)
2. New 321 stainless steel header (排氣頭段, 要 雙孔還是要單孔)
3. Gaskets, header to engine (排氣管墊片)
4. Smallcar engine mount with mounting hardware (引擎托架)
5. Heavy duty muffler mounts and stainless clamps (specify muffler diameter when ordering) (排氣尾段 支架)
6. Accelerator cable kit ( 油門線 )
7. Coolant hose kit with clamps (designed for reversed coolant manifold) (冷卻水管組)
8. Coolant reservoir bracket ( 附水桶 支架)
9. Harness modification kit - our do-it-yourself diagrams and guide ( 線組改裝圖)
10.  Aluminum oil pan for better oil capacity with stock ground clearance (also allows refitting of the Syncro skid plate)  (鋁製淺油底殼)
11. Flexible dipstick , allows checking of oil level from license plate door( 機油尺)
12. All years of Vanagon and all years 2.2 or 2.5L engines - reversed coolant manifold & heater pipe (反置subaru 上水管)

以下零件, 早期T3沒有的, 要加購.
The following should be purchased if you have a 1985 and earlier Vanagon

• 1986 and later coolant reservoir
• 1986 and later style exhaust connector, J pipe
• 1983-85 original front-rear coolant pipes will require 1 hose reducer.

以下為選購

The following optional parts are recommended for the models indicated:

• All power steering equipped Vanagons - power steering hose (動力方向盤管路)
• All engines - speed sensor kit (輪速感應器)
• Installations with 2000-2011 Subaru engines - intake hose kit (進氣管, 需視EJ引擎而定)
• Installations with VVT Subaru engines - Fuel pressure regulator
• All years of automatic Vanagons, eliminate the troublesome transmission cooler- TCK transmission cooler kit (變速箱冷卻)
• Any year Vanagon - New rubber engine mounts (引擎腳)
• All drive by wire engines - Mount spacer, A/T pedal kit (線傳引擎用油門線)
• Any Vanagon as needed stainless, stock or performance muffler and tailpipe
• 1986 and later Vanagons with 1999 and later Subaru engines or anywhere a 7,000 RPM redline is desired - Tachometer unit and Gauge face (轉速表)
• Any combination, substitute our harness modification service for the harness modification kit $100 discount with parts kit above - Harness modification (改裝線組折價$100)
• For 1995 and later engines oxygen sensor bung for 2nd sensor 
• For 1996 and later engines Interface board to eliminate 7-8 common ECU fault codes (消除錯誤碼用)
• Recommended gear reduction starter (強力起動碼達)
• For 1996-2011 engines ScanGauge II driving computer (引擎監控scanGauge)

205/55/R16 wheel has circumference 1.985m

120km/h= 33.33 m/s => 16.8 turns/sec

if 4 pulse a turn => 67.2pulses/second @120km/h => 14.88ms between pulses.

if 6 pulse a turn => 100.8pulses/second @120km/h => 99us between pulses.

Vanagon stock rim

14", 5H112, 6J, ET30
thickness at screw hole is 18mm.

stock stud is 25mm out of hub.

Vanagon Syncro steel wheel

6Jx14, ET30, ball set.

944 phone dial rim

Front 16x7J, ET52, Ball set

Rear 16x8J, ET52, Ball set

to fit on a Vanagon, need a spacer transform 5H112 to 5H130, with thickness 20mm or more.

Fit Blaupunkt Stereo on Vanagon Carat

Fits perfectly, BLAUPUNKT CASABLANCA CM 62

Measurement log of fitting W211 rim on Vanagon T3

W211 forged wheel on T3

16", 5H112, 7.5J ET33, 肉厚 9mm, thickness 9mm, Ball set

前輪離羊角有段距離, 免墊片, 有墊片或修改grees cap時中心標可上.

後面可免墊, 但無法直上中心標, 須加墊片才能上中心標. 螺栓需加長.

Dry fit, no spacer

須加墊片才能上中心標. 螺栓需加長.

need a spacer for fitting center cap, and longer bolt of course.

前輪離羊角有段距離, 免墊片, 有墊片或修改grees cap時中心標可上.

Still has some space from upper arm, 

 這框比較斯文, 適合美規車
look good on Carat. but not on Syncro.

後面可免墊, 但無法直上中心標, 須加墊片才能上中心標. 螺栓需加長.

Still has some space from rear control arm, spacer is not necessary if certer cap is not considered.

後輪不會超過輪拱
Wheel did not exceed body.

Measurement log of fitting W220 rim on Vanagon T3

W220 forged wheel on T3

16", 5H112, 7.5J ET46, 肉厚24mm. thickness 24mm, ball set.

前輪已卡住羊角, 要墊15mm 左右, 有墊片時中心標可上.

後面可免墊, 中心標小修改可上. 螺栓需加長.

Dry fit, no spacer

前輪已卡住羊角,,要墊15mm 左右, 有墊片時中心標可上.

from wheel touched upper arm, need a 15mm spacer at least on Vanagon, not sure if it is the same on a Syncro.

這匡比較適合四傳+AT胎.

It will be looking good with AT tyre on Syncro.

後面可免墊

no spacer for rear wheel.

沒墊片時不會超過輪拱.
Wheel will not exceed body.

Picture log of futureVSS location

Vanagon Carat 3AT tranny, driver side, where speed sensor will be fitted.

6 pulses a turn.

Sensor will be a proximity sensor, which sense bolt on transaxle.

EJ22 on a 96 Subaru Legacy, run 13k km already still very smooth.

mobile Lab on Vanagon Carat, testing GPS speedo and digital tachometer

Test GPS speedometer

Test digital tachometer.